CFTXF - ACRY-PLEX FLAT WALL ENAMEL, 555-SERIES (ALL COLORS)

  • MSDS: CFTXF
  • Manufacturer: KELLY MOORE PAINT CO INC
  • Product Name: ACRY-PLEX FLAT WALL ENAMEL, 555-SERIES (ALL COLORS)
  • National Stock Number: 8010-00N081608
Product Identification

Product ID:ACRY-PLEX FLAT WALL ENAMEL, 555-SERIES (ALL COLORS)
MSDS Date:09/20/1994
FSC:8010
NIIN:00N081608
MSDS Number: CFTXF

Responsible Party
KELLY-MOORE PAINT CO INC
1015 COMMERCIAL ST
SAN CARLOS, CA 94070
US

Emergency Phone: 800-424-9300 (CHEMTREC)

Info Phone: 415-592-8337

Preparer: JULIAN SHAFFER

Cage: 0Y837

Contractor
KELLY-MOORE PAINT CO INC
SAN CARLOS, CA 94070 US

Telephone: 650-592-8337

Cage: 0Y837

Ingredients

PROPIONIC ACID, 2-METHYL-, MONOESTER WITH

CAS: 25265-77-4

RTECS: UF6000000

OSHA PEL N/K

ACGIH TLV: N/K


SILICATES; (MINERAL SILICATES)

OSHA PEL 10 MG/M3

ACGIH TLV: 10 MG/M3


CALCIUM CARBONATE (MARBLE) (LIMESTONE)

CAS: 1317-65-3

RTECS: EV9580000

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9495


TITANIUM OXIDE; (TITANIUM DIOXIDE)

CAS: 13463-67-7

RTECS: XR2275000

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9495


SILICA, CRYSTALLINE - QUARTZ

CAS: 14808-60-7

RTECS: VV7330000

Fraction By Weight: TRACE

OSHA PEL SEE TABLE Z-3

ACGIH TLV: 0.1 MG/M3 RDUST;9495


4-ISOTHIAZOLIN-3-ONE, 5-CHLORO-2-METHYL-; (PAINT

CAS: 26172-55-4

RTECS: NX8156850

OSHA PEL N/K

ACGIH TLV: N/K

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: DIZZINESS, HEADACHE, NAUSEA,
CONFUSION, IRRITATION TO UPPER RESPIRATORY TRACT, UNCONSCIOUSNESS,
SKIN AND EYE IRRITATION. CHRONIC: NONE KNOWN.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARD.
Medical Cond Aggravated by Exposure:NONE KNOWN. SEE YOUR PHYSICIAN FOR
SPECIFIC MEDICAL OPINION REGARDING YOUR CONDITION.

First Aid

First Aid:INHALATION: REMOVE TO FRESH AIR. RESTORE BREATHING. CONSULT
PHYSICIAN. EYE CONTACT: FLUSH WITH LARGE VOLUMES OF WATER FOR AT
LEAST 15 MINUTES. GET MEDICAL ATTENTION. SKIN CONTACT: WIPE OFF
WITH A RAG. WASH THOROUGHLY WITH SOAP AND WATER. INGESTION:
CONSULT HOSPITAL EMERGENCY ROOM OR POISON CONTROL CENTER
IMMEDIATELY.

Fire Fighting

Flash Point:NONE
Extinguishing Media:MEDIA SUITABLE FOR SURROUNDING FIRE .
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE (DUE TO THE
BUILD-UP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME HEAT.

Accidental Release

Spill Release Procedures:VENTILATE AREA TO PREVENT BUILD-UP OF VAPORS.
FOR SMALL SPILLS, SOAK UP WITH ABSORBANT. FOR LARGER SPILLS, DIKE
AREA WITH ABSORBENT MATERIAL AND SCOOP UP LIQUIDS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:STORE UPRIGHT IN SEALED CONTAINERS
AWAY FROM HEAT AND FLAME.
Other Precautions:REMOVE AND WASH CONTAMINATED CLOTHING BEFORE REUSE.

Exposure Controls

Respiratory Protection:USE A PARTICLE MASK (NIOSH TC-21C) TO AVOID
BRTHG SPRAY MIST/SANDING DUST IF LOCAL VENT IS ADEQ TO KEEP VAP
CONC W/IN ACCEPTABLE (TVL) LIMS. IF LOCAL VENT IS NOT
SUFFICIENT/WHERE EXPOS LIMS ARE EXCEED ED. WEAR A SUITABLE (SUPDAT)
Ventilation:LOCAL CROSS-VENT OR MECHANICAL EXHAUST SUFFICIENT TO KEEP
ALL HAZARDOUS VAPOR CONCENTRATIONS BELOW PRESCRIBED LIMITS.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:EYE WASH FOUNTAIN & DELUGE SHOWER WHICH MEET
ANSI DESIGN CRITERIA .
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
RESP PROT: PROPERLY FITTED RESPIRATOR (NIOSH TC-23C OR BETTER) FOR
ORGANIC VAPORS WITH A DUST FILTER AS NEEDED.

Chemical Properties

Boiling Pt:B.P. Text:212F,100C
Vapor Density:LTR/AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:60-65

Stability

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:NOT APPLICABLE.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
HEATED TO DECOMPOSITION AS IN WELDING.

Disposal

Waste Disposal Methods:DISCARD IN LANDFILL IN SEALED METAL CONTAINERS
AWAY FROM HEAT AND FLAME AND IN ACCORDANCE WITH FEDERAL, STATE AND
LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.